EAW DX810 Instruction Manual download pdf (Page 26)

26 – DX810

reflected in the Crosspoint Matrix Section by “blanking

out” all but the top row of crosspoints for the linked

crossover outputs. Note that only contiguous outputs

may be linked to create a crossover.

Linking outputs together for the crossover

automatically links those outputs in Output EQ

processors. The Output EQ defaults to the setting

for the first output in the crossover (i.e., Output A).

The equalizers are located prior to the crossover in

the signal chain, so all the outputs assigned to the

crossover are affected by the EQ settings.

With the first band active (red active button lit),

click the On button to turn the crossover on and off.

When the crossover is turned off, all the outputs

assigned to the crossover pass a full-range signal.

Click the Reset button to return all the knobs for the

currently active band to their default settings.

Output:

Select the first output for the crossover

(A-J). Click the arrow next to the box to select an

output in the pull-down list. It appears in the first

Output box. Repeat for up to five bands in a single

crossover system.

To deselect an output once you've selected one,

click the arrow next to the box and select the

"blank" line under the J output. This removes the

output selection from the crossover.

Polarity:

The Polarity button reverses the

polarity of the output by 180°.

Edit:

Click the Active button under Edit to adjust

the settings for the selected output. Then use the

Filter Type, Filter Slope, Alignment, Frequency,

and Delay Time controls.

Filter Type:

Use this control to select high-pass

(HP), low-pass (LP), or band-pass (BP) filters for the

selected output. Notice that the Frequency control

selection changes to High Freq and Low Freq

when BP is selected.

Filter Slope:

Use this control to choose the roll-off

curve for the frequencies above or below the cutoff

frequency. When Butterworth or Bessel alignment is

selected, 12, 18, and 24 dB/octave slopes are

available. When Linkwitz-Riley is selected, 12 and

24 dB/octave are available (18 dB can’t be selected).

Alignment:

This switch selects either Linkwitz-

Riley, Butterworth, or Bessel characteristics for the

selected Filter Type.

Frequency:

This selects the cutoff frequency for

the selected filter, with a range from 20 Hz to 20

kHz. When a bandpass filter is selected, High Freq

and Low Freq controls are available.

Delay Time:

This control adjusts the delay for

the selected output in small increments (22.7 µs),

with a range from 0 µs to 997 µs. The equivalent

distance the sound travels in the selected amount

of time is displayed.

Note: This control is provided in the Crossover

window because the Delay Line DSP (the Delay

button) is situated prior to the crossover in the signal

chain. When the crossover is active, use this delay

control to adjust for offsets between drivers in a

stack. For example, use this control to time-align a

horn’s compression driver and a woofer’s voice coil.

Option

This button is reserved for future upgrades.

CROSSPOINT MATRIX SECTION

This section provides a view of all the input-to-

output crosspoints in the mixing matrix. It has a

numerical and graphical indication of the gain

setting for each crosspoint.

Click the associated letter button (A-J) in the

Output Section to select an output and the

horizontal row of input crosspoints is highlighted.

The input faders in the Input Section now control

the gain settings and mix for the selected output.

Either click on the fader or click on the horizontal

mini-fader indicator bar in the crosspoint to adjust

the gain for the input.

Click the select (S) button to select the

crosspoint for copying or pasting the level.

Otherwise, when a group is selected, use it to

assign the crosspoint to the selected group.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 35 36

Comments to this Manuals

No comments

EAW DX810 Instruction Manual Page 26

Comments to this Manuals

Related products and manuals for Processors EAW DX810