Eaw UX8800 User Manual download pdf (Page 23)

6.5.2 U-NET OUT ASSIGN

Assign the processed output signal to a U-Net output channel: U-Net 1 to 32

6.5.3 CHANNEL NAME

Enter a name for the output channel, up to 16 alphanumeric characters.

6.6 LEVEL

Use the LEVEL function to set Input Channel and Output Channel gain and polarity by selecting the Ato

D or 1 to 8 buttons.

Level: Scroll through and select the gain up to +/- 15 dB in 0.1 dB steps.

Polarity: Select the polarity: + or -.

6.7 X-OVER (Output Channels 1 to 8)

Use the X-OVER function to set crossover filters for providing an acoustic transition between a multi-

amplified loudspeaker’s subsystems. The crossover filters have the following variable parameters:

HPF / LPF High Pass Filter / Low Pass Filter

Filt: Set the selected HPF or LPF to be active or inactive.

Freq: Scroll through and select the crossover filter frequency from 20 Hz to 20 kHz in

1/24th Octave steps.

Type: Scroll through and select the crossover type and slope:

6 dB Butterworth, Bessel

12 dB Butterworth, Bessel, Linkwitz-Riley

18 dB Butterworth, Bessel

24 dB Butterworth, Bessel, Linkwitz-Riley

30 dB Butterworth, Bessel

36 dB Butterworth, Bessel, Linkwitz-Riley

42 dB Butterworth, Bessel

48 dB Butterworth, Bessel, Linkwitz-Riley

6.8 LIM (Output Channels 1 to 8)

Use the LIM function to set the compressor / limiter parameters:

Lim: Sets the Comp/Lim to In (active) or Out (inactive).

Thrsh: Scroll through and select the limiter threshold from 20 dBu to -10 dBu in 0.1 dB steps.

Ratio: Scroll through and select the compression ratio in integer increments:

1:1 to 20:1, or Inf:1.

Atk: Scroll through and select the limiter attack from 40 µs to 1 ms in 10 µs steps, 1

ms to 40 ms in 1 ms steps. The default setting is 1 ms.

Rel: Scroll through and select the limiter release from 10 ms to 2 s in 10 ms steps.

Knee: Select the aggressiveness of the onset of limiting between a hard or soft knee.

6.9 EQ

Use the EQ function to set the Input Channel and Output Channel equalization by selecting the A to D or

1 to 8 buttons. Each channel’s EQ section has 10 filters. Each EQ section has the following variable

parameters. The available parameters depend on the selected Type.

Parametric EQ: Sets the entire EQ section (filters 1 to 10) to In (active) or Out (inactive).

Type: Scroll through and select the type for each parametric filter: Bell, 6 dB LoShelf,

12 dB LoShelf, 6 dB HiShelf, 12 dB HiShelf, 6 dB HPF, 12 dB HPF, 6 dB LPF,

or 12 dB LPF.

BW: Scroll through and select the bandwidth for each filter: 0.02 to 10 octaves.

Freq: Scroll through and select the frequency for each filter: Variable from 20 Hz to

20 kHz in 1/24th octave steps.

Gain: Scroll through and select the gain for each filter: +/- 15 dB in 0.1 dB steps.

Filt: Sets the selected filter (1 to 10) to be In (active) or Out (inactive).

Page 13

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 39 40

Comments to this Manuals

No comments

Eaw UX8800 User Manual Page 23

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Eaw UX8800